三台路由器静态路由无法ping通的有关问题？

请教高手三台路由器静态路由无法ping通的问题？？？


  在两台电脑中设置IP地址后，再为3台路由器设置IP地址和静态路由.代码如下：
先设置IP地址
Router0
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface f0/0
Router(config-if)#ip address 192.168.1.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
Router(config-if)#interface s2/0
Router(config-if)#ip address 192.168.2.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#

Router1
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface s2/0
Router(config-if)#ip address 192.168.2.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config-if)#interface s3/0
Router(config-if)#ip address 192.168.3.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#

Router3
Router>enable
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface f0/0
Router(config-if)#ip address 192.168.4.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
Router(config-if)#interface s2/0
Router(config-if)#ip address 192.168.3.2 255.255.255.0
Router(config-if)#no shutdown

在为3台路由器设置静态路由：
Router0
Router(config-if)#exit
Router(config)#ip route 192.168.3.0 255.255.255.0 192.168.2.2
Router(config)#ip route 192.168.4.0 255.255.255.0 192.168.2.2
Router(config)#exit

Router1
Router(config-if)#exit
Router(config)#
Router(config)#ip route 192.168.1.0 255.255.255.0 192.168.2.1
Router(config)#ip route 192.168.4.0 255.255.255.0 192.168.3.2
Router(config)#exit

Router3
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#ip route 192.168.1.0 255.255.255.0 192.168.3.1
Router(config)#ip route 192.168.2.0 255.255.255.0 192.168.3.1
Router(config)#exit

废话写了这么多！！后来我把clock rate命令删除后，发现两台电脑无法ping通了。为什么？难道非要这条命令不可吗？


------解决方案--------------------
是啊。就是同步速率，大家说话速度不一致，没法沟通
------解决方案--------------------

探讨

是啊。就是同步速率，大家说话速度不一致，没法沟通

------解决方案--------------------

探讨

是啊。就是同步速率，大家说话速度不一致，没法沟通