现象如题.
发送中断是可以进去的。
想了很久没想到原因在哪，求帮助。
代码如下：
void NVIC_Configuration()
{
NVIC_InitTypeDef NVIC_InitStructure;
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2);
NVIC_InitStructure.NVIC_IRQChannel = UART4_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
NVIC_InitStructure.NVIC_IRQChannel = USART2_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 2;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
}
void Uart2_Init(u32 nBaud)
{
USART_InitTypeDef USART_InitStructure;
GPIO_InitTypeDef GPIO_InitStructure;
//
USART_DeInit(USART2);
//
RCC_AHB1PeriphClockCmd(UART2_TX_GPIO_CLK|UART2_RX_GPIO_CLK,ENABLE);
RCC_APB1PeriphClockCmd(UART2_CLK,ENABLE);
//
GPIO_PinAFConfig(UART2_TX_GPIO_PORT,UART2_TX_PIN,GPIO_AF_USART2);
GPIO_PinAFConfig(UART2_RX_GPIO_PORT,UART2_RX_PIN,GPIO_AF_USART2);
//TX
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_UP;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Pin = UART2_TX_PIN;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(UART2_TX_GPIO_PORT,&GPIO_InitStructure);
//RX
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF;
GPIO_InitStructure.GPIO_Pin = UART2_RX_PIN;
GPIO_Init(UART2_RX_GPIO_PORT,&GPIO_InitStructure);
//
USART_InitStructure.USART_BaudRate = nBaud;
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
USART_InitStructure.USART_StopBits = USART_StopBits_1;
USART_InitStructure.USART_Parity = USART_Parity_No ;
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
USART_Init(USART2, &USART_InitStructure);
USART_ITConfig(USART2, USART_IT_RXNE, ENABLE);
USART_ITConfig(USART2, USART_IT_TXE, ENABLE);
USART_Cmd(USART2, ENABLE);
//·???????????????·¨·?????????
//USART_GetITStatus(USART2, USART_FLAG_TC);
}
void USART2_IRQHandler(void)
{
//
if (USART_GetFlagStatus(USART2, USART_FLAG_ORE) != RESET)
{
USART_ReceiveData(USART2);