#include<reg52.h>
#include<delay.h> //1MS延时
#define uchar unsigned char
#define uint unsigned int
#define hang P1 //行扫描接在P1口
sbit ds=P0^0;
sbit clk=P0^1;
sbit mr=P0^2;
sbit g1=P0^3;
sbit stcp=P0^4;
uint counter;
uchar flag;
uchar code display[][32]={
/*-- 文字: 好 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
0x10,0x00,0x11,0xFC,0x10,0x08,0x10,0x10,0xFC,0x20,0x24,0x20,0x24,0x20,0x27,0xFE,
0x44,0x20,0x64,0x20,0x18,0x20,0x08,0x20,0x14,0x20,0x26,0x20,0x44,0xA0,0x80,0x40,
/*-- 文字: 好 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
0x10,0x00,0x11,0xFC,0x10,0x08,0x10,0x10,0xFC,0x20,0x24,0x20,0x24,0x20,0x27,0xFE,
0x44,0x20,0x64,0x20,0x18,0x20,0x08,0x20,0x14,0x20,0x26,0x20,0x44,0xA0,0x80,0x40,
/*-- 文字: 学 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
0x01,0x08,0x10,0x8C,0x0C,0xC8,0x08,0x90,0x7F,0xFE,0x40,0x04,0x8F,0xE8,0x00,0x40,
0x00,0x80,0x7F,0xFE,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x02,0x80,0x01,0x00,
/*-- 文字: 习 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
0x00,0x00,0x3F,0xFC,0x00,0x04,0x08,0x04,0x04,0x04,0x03,0x04,0x01,0x14,0x00,0x64,
0x01,0x84,0x06,0x04,0x38,0x04,0x10,0x04,0x00,0x04,0x00,0x24,0x00,0x14,0x00,0x00,
/*-- 文字: 天 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
0x00,0x08,0x7F,0xFC,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x04,0xFF,0xFE,0x01,0x00,
0x02,0x80,0x02,0x80,0x04,0x40,0x04,0x40,0x08,0x20,0x10,0x10,0x20,0x0E,0xC0,0x04,
/*-- 文字: 天 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
0x00,0x08,0x7F,0xFC,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x04,0xFF,0xFE,0x01,0x00,
0x02,0x80,0x02,0x80,0x04,0x40,0x04,0x40,0x08,0x20,0x10,0x10,0x20,0x0E,0xC0,0x04,
/*-- 文字: 向 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
0x02,0x00,0x04,0x00,0x08,0x04,0x7F,0xFE,0x40,0x04,0x40,0x24,0x4F,0xF4,0x48,0x24,
0x48,0x24,0x48,0x24,0x48,0x24,0x4F,0xE4,0x48,0x24,0x40,0x04,0x40,0x14,0x40,0x08,
/*-- 文字: 上 --*/
/*-- 宋体12; 此字体下对应的点阵为：宽x高=16x16 --*/
0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x10,0x01,0xF8,0x01,0x00,0x01,0x00,
0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x04,0xFF,0xFE,0x00,0x00};
void write_595(uchar shuju) //向595写一个字节的数据
{
uchar i;
for(i=0;i<8;i++)
{
ds=(~shuju)&0x01;
clk=1;
clk=0;
shuju=shuju>>1;
}
}
void main() //主函数
{
uchar i,j,k;
g1=0; //154使能
EA=1; //开总中断
TMOD=0x01; //定时器0工作方式0
ET0=1; //定时器0使能
TH0=(65535-50000)/256; //定时器0设置初值
TL0=(65536-50000)%256;
while(1)
{
for(i=0;i<16;i++) //字从下往上滚动出现
{
k=1;
for(j=i+1;j>0;j--)
{
write_595(display[7][k]);
write_595(display[7][k-1]);
write_595(display[6][k]);
write_595(display[6][k-1]);
write_595(display[5][k]);
write_595(display[5][k-1]);
write_595(display[4][k]);
write_595(display[4][k-1]);
k+=2;
hang=16-j;
stcp=1;stcp=0;